When you first create a new Ubuntu 18.04 server, there are a few configuration steps that you should take early on as part of the basic setup. This will increase the security and usability of your server and will give you a solid foundation for subsequent actions.

Note: The guide below demonstrates how to manually complete the steps we recommend for new Ubuntu 18.04 servers. Following this procedure manually can be useful to learn some basic system administration skills and as an exercise to fully understand the actions being taken on your server.

Step 1 — Logging in as Root

To log into your server, you will need to know your server’s public IP address. You will also need the password or, if you installed an SSH key for authentication, the private key for the root user’s account.

If you are not already connected to your server, go ahead and log in as the root user using the following command (substitute the strikethrough portion of the command with your server’s public IP address):

$ ssh root@your_server_ip

Accept the warning about host authenticity if it appears. If you are using password authentication, provide your root password to log in. If you are using an SSH key that is passphrase protected, you may be prompted to enter the passphrase the first time you use the key each session. If this is your first time logging into the server with a password, you may also be prompted to change the root password.

About Root

The root user is the administrative user in a Linux environment that has very broad privileges. Because of the heightened privileges of the root account, you are discouraged from using it on a regular basis. This is because part of the power inherent with the root account is the ability to make very destructive changes, even by accident.

The next step is to set up an alternative user account with a reduced scope of influence for day-to-day work. We’ll teach you how to gain increased privileges during the times when you need them.

Step 2 — Creating a New User

Once you are logged in as root, we’re prepared to add the new user account that we will use to log in from now on.

This example creates a new user called creaholik, but you should replace it with a username that you like:

# adduser creaholik

You will be asked a few questions, starting with the account password.

Enter a strong password and, optionally, fill in any of the additional information if you would like. This is not required and you can just hit ENTER in any field you wish to skip.

Step 3 — Granting Administrative Privileges

Now, we have a new user account with regular account privileges. However, we may sometimes need to do administrative tasks.

To avoid having to log out of our normal user and log back in as the root account, we can set up what is known as “superuser” or root privileges for our normal account. This will allow our normal user to run commands with administrative privileges by putting the word sudo before each command.

To add these privileges to our new user, we need to add the new user to the sudo group. By default, on Ubuntu 18.04, users who belong to the sudo group are allowed to use the sudo command.

As root, run this command to add your new user to the sudo group (substitute the highlighted word with your new user):

# usermod -aG sudo creaholik

Now, when logged in as your regular user, you can type sudo before commands to perform actions with superuser privileges.

Step 4 — Setting Up a Basic Firewall

Ubuntu 18.04 servers can use the UFW firewall to make sure only connections to certain services are allowed. We can set up a basic firewall very easily using this application.

Different applications can register their profiles with UFW upon installation. These profiles allow UFW to manage these applications by name. OpenSSH, the service allowing us to connect to our server now, has a profile registered with UFW.

You can see this by typing:

# ufw app list

Output
Available applications:
OpenSSH

We need to make sure that the firewall allows SSH connections so that we can log back in next time. We can allow these connections by typing:

# ufw allow OpenSSH

Afterwards, we can enable the firewall by typing:

# ufw enable

Type “y” and press ENTER to proceed. You can see that SSH connections are still allowed by typing:

# ufw status

Output
Status: active

To                         Action      From
--                         ------      ----
OpenSSH                    ALLOW       Anywhere
OpenSSH (v6)               ALLOW       Anywhere (v6)

As the firewall is currently blocking all connections except for SSH, if you install and configure additional services, you will need to adjust the firewall settings to allow acceptable traffic in.

Step 5 — Enabling External Access for Your Regular User

Now that we have a regular user for daily use, we need to make sure we can SSH into the account directly.

Note: Until verifying that you can log in and use sudo with your new user, we recommend staying logged in as root. This way, if you have problems, you can troubleshoot and make any necessary changes as root.

The process for configuring SSH access for your new user depends on whether your server’s root account uses a password or SSH keys for authentication.

If the Root Account Uses Password Authentication

If you logged in to your root account using a password, then password authentication is enabled for SSH. You can SSH to your new user account by opening up a new terminal session and using SSH with your new username:

$ ssh creaholik@your_server_ip

After entering your regular user’s password, you will be logged in. Remember, if you need to run a command with administrative privileges, type sudo before it like this:

$ sudo command_to_run

You will be prompted for your regular user password when using sudo for the first time each session (and periodically afterwards).

Where To Go From Here?

At this point, you have a solid foundation for your server. You can install any of the software you need on your server now.